The Chimney Sweep Online Fireplace, Woodstove, Gas Stove and Barbecue Shop
The Chimney Sweep Online Fireplace, Woodstove, Gas Stove and Barbecue Shop
STOVE MODEL: HEARTHSTONE TUCSON DIRECT VENT GAS STOVE STOVE DIMENSIONS: 21" WIDE X 14 1/2" DEEP X 25" TALL CONNECTOR PIPE USED: 6 5/8" COAXIAL DIRECT VENT PIPE
NO HEARTH (FLOOR PROTECTION) NEEDED ON WOOD FLOOR MINIMUM HEARTH REQUIRED ON CARPET, VINYL, ETC: 21"W X 14 1/2"D (SAME SIZE AS STOVE)
VENTING OPTIONS: VERTICAL VENT: STRAIGHT UP THROUGH CEILING, ROOFING AND ROOF FLASHING TO A 6 5/8" ROUND CAP DIRECT VENT: UP 9" THEN ELBOW THROUGH BACKWALL TO SQUARE 13 1/2"T x 13 1/2"W x 5 3/8"D CAP SNORKEL VENT: STRAIGHT BACK (STOVE HIDES PIPE), TO 28 1/2"T x 13 1/2"W x 10"D "SNORKEL" CAP THROUGH FIREPLACE: ADAPTER TO 3"/3" CO-LINEAR FLEX PIPE THRU SEALER PLATE AT TOP OF CHIMNEY
FLAT BACKWALL CORNER BASIC DIRECT VENT SNORKEL VENT
FLAT WALL INSTALLATIONS | CORNER INSTALLATIONS |
A: STOVE TO BACKWALL IF VERTICAL/DIRECT VENTED.... 5-3/8" IF SNORKEL VENTED................ 3" | G: STOVE CORNERS TO CORNER WALLS....... 2" |
B: STOVE TO SIDEWALL................ 2" | H: CENTERLINE OF VERTICAL PIPE TO CORNER WALLS................ 9-7/16" |
C: CENTERLINE OF VERTICAL PIPE TO BACKWALL.................. 5-3/8" | I: CORNER TO CENTERLINE OF PIPE... 13-3/8" TO FRONT OF WINDOW................. 28" |
D: CENTERLINE OF VERTICAL PIPE TO SIDEWALL................. 12-1/2" | M: FLOOR TO CENTERLINE OF EXHAUST PIPE IF DIRECT VENTED................... 39" IF SNORKEL VENTED.............. 22-1/4" |
E: BACKWALL TO FRONT OF DOOR: IF VERTICAL/DIRECT VENTED....... 20" IF SNORKEL VENTED........... 17-1/2" | N: FLOOR TO TOP OF HORIZONTAL VENT CAP IF DIRECT VENTED................... 46" IF SNORKEL VENTED.................. 43" |
COMBUSTIBLE ALCOVE DIMENSIONS: MINIMUM 25"W X 44 1/4"T, MAXIMUM 17"D
MINIMUM FIREPLACE OPENING HEIGHT (FIREPLACE HEARTH INSTALLATIONS): 26"
TOP OF STOVE TO OVERHANGING COMBUSTIBLES: 16"
 | FIREPLACE HEARTH INSTALLATIONS:Determine the height of the chimney, and purchase enough 3" flexible aluminum liner to extend to the top of the chimney twice.Attach the two lengths of aluminum flex liner to the intake and exhaust ports on the top adapter box with pipe clamps or sheet metal screws and silicone sealant. Glue the top sealer plate to the chimney top with silicone sealant, and lower the two liner lengths through the opening. Anchor the top adapter box to the sealer plate with screws, and twist-lock the coaxial rain cap on top. Down below, use clamps or screws and silicone sealant to attach the two liner lengths to the bottom adapter box, which is used to connect the liners to a coaxial 45 degree elbow. The elbow then connects to the 45 degree flue collar on the stove.If the stove is to stand inside the fireplace, orient the 45 degree elbow so it points straight up, as shown in the diagram at upper right. If the stove is to stand out on the hearth in front of the fireplace opening as shown at lower right, orient the elbow so it points straight back to clear the lintel bar, then bend the liners forward to attach the adapter box. |
|
|
(our reply form)
